Summary

Hello,

here you can find an coin with exact dimensions of an one euro coin. Features: The bottom layers are smaller in diameter to compensate the bigger printed bottom layers. With or without whole.

MrSkyballer

Instructions

Here you have the parameter I have used while printing with my Ultimaker 1.

[profile]
layer_height = 0.1
wall_thickness = 0.8
retraction_enable = True
solid_layer_thickness = 0.3
fill_density = 20
nozzle_size = 0.37
print_speed = 50
print_temperature = 220
print_temperature2 = 0
print_temperature3 = 0
print_temperature4 = 0
print_bed_temperature = 70
support = None
platform_adhesion = None
support_dual_extrusion = Both
wipe_tower = False
wipe_tower_volume = 15
ooze_shield = False
filament_diameter = 2.85
filament_diameter2 = 0
filament_diameter3 = 0
filament_diameter4 = 0
filament_flow = 130.0
retraction_speed = 40.0
retraction_amount = 4.5
retraction_dual_amount = 16.5
retraction_min_travel = 1.5
retraction_combing = True
retraction_minimal_extrusion = 0.02
bottom_thickness = 0.25
object_sink = 0.0
overlap_dual = 0.15
travel_speed = 150.0
bottom_layer_speed = 20
infill_speed = 0.0
cool_min_layer_time = 5
fan_enabled = True
skirt_line_count = 1
skirt_gap = 3.0
skirt_minimal_length = 150.0
fan_full_height = 0.5
fan_speed = 100
fan_speed_max = 100
cool_min_feedrate = 10
cool_head_lift = False
solid_top = True
solid_bottom = True
fill_overlap = 15
support_fill_rate = 15
support_xy_distance = 0.7
support_z_distance = 0.15
spiralize = False
brim_line_count = 20
raft_margin = 5
raft_line_spacing = 1.0
raft_base_thickness = 0.3
raft_base_linewidth = 0.7
raft_interface_thickness = 0.2
raft_interface_linewidth = 0.2
fix_horrible_union_all_type_a = True
fix_horrible_union_all_type_b = False
fix_horrible_use_open_bits = False
fix_horrible_extensive_stitching = False
plugin_config = (lp1
.
object_center_x = -1
object_center_y = -1

[alterations]
start.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
;Filament cost: {filament_cost}
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
;M109 S{print_temperature} ;Uncomment to add your own temperature line
G21 ;metric values
G90 ;absolute positioning
M107 ;start with the fan off

G28 X0 Y0  ;move X/Y to min endstops  G28 Z0     ;move Z to min endstops  G1 Z15.0 F{travel_speed} ;move the platform down 15mm  G92 E0                  ;zero the extruded length  G1 F200 E3              ;extrude 3mm of feed stock  G92 E0                  ;zero the extruded length again  G1 F{travel_speed}  ;Put printing message on LCD screen  M117 Printing...

end.gcode = ;End GCode
M104 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)

G91                                    ;relative positioning  G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure  G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more  G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way  M84                         ;steppers off  G90                         ;absolute positioning

start2.gcode = ;Sliced at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
;Filament cost: {filament_cost}
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
;M104 S{print_temperature} ;Uncomment to add your own temperature line
;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
G21 ;metric values
G90 ;absolute positioning
M107 ;start with the fan off

G28 X0 Y0  ;move X/Y to min endstops  G28 Z0     ;move Z to min endstops  G1 Z15.0 F{travel_speed} ;move the platform down 15mm  T1                      ;Switch to the 2nd extruder  G92 E0                  ;zero the extruded length  G1 F200 E10             ;extrude 10mm of feed stock  G92 E0                  ;zero the extruded length again  G1 F200 E-{retraction_dual_amount}  T0                      ;Switch to the first extruder  G92 E0                  ;zero the extruded length  G1 F200 E10             ;extrude 10mm of feed stock  G92 E0                  ;zero the extruded length again  G1 F{travel_speed}  ;Put printing message on LCD screen  M117 Printing...

end2.gcode = ;End GCode
M104 T0 S0 ;extruder heater off
M104 T1 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)

G91                                    ;relative positioning  G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure  G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more  G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way  M84                         ;steppers off  G90                         ;absolute positioning

support_start.gcode =
support_end.gcode =
cool_start.gcode =
cool_end.gcode =
replace.csv =
switchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
G92 E0
G1 E-36 F5000
G92 E0
T{extruder}
G1 X{new_x} Y{new_y} Z{new_z} F{travel_speed}
G1 E36 F5000
G92 E0

euro chip for shopping cart / supermarket trolley