• 3D Mesh Market
  • Print
  • Discover
    •  Login Signup

    RC Car based on DC Motor 550

    This RC Car is completely designed by me.

    Print List

    RC Pad

    • 006-001_RC_Pad.stl

    Car

    • 2x 001-001_Frame.stl ABS recommended -- due to motor can be too hot for PLA
    • 2x 001-002 Battery Holder Support.stl
    • 1x 001-003 Cable Holder.stl (optional)
    • 1x 001-004 Underframe.stl
    • 1x 002-001 Secondary Gear.stl
    • 1x 002-002 Primary Gear.stl
    • 4x 003-001 Rim.stl
    • 4x 003-002 Tire.stl SEBS/Rubber material recommended
    • 1x 004-001 Steering Clamp.stl
    • 2x 004-002 Rod End.stl
    • 2x 004-003 Lower Arm.stl
    • 1+1 004-006 Steering Knuckle B.stl (one original + one mirrored)
    • 2x 004-104 Arm Bushing.stl
    • 1x 004-105 Normal enforcer.stl
    • 1x 005-001 Hood C.stl
    • 1x 005-002 Front Panel.stl
    • 1x 005-003 Front Bumper B.stl
    • 1x 005-004 Hood Holder.stl
    • 1x 005-005 Front Hood.stl

    Here is the list of electronic components you'll have to get:

    For the Car

    1. Arduino Nano -- controller_
    2. NRF24L01+ -- 2.4GHz radio module
    3. L298N -- Dual full bridge dc-motor driver
    4. DSN-MINI-360 -- DC-DC Buck converter
    5. 100uF 16V capacitor -- for radio module
    6. 3pcs 2N3904 -- NPN bipolar junction transistor
    7. 3pcs 100Ohms resistor
    8. 10Ohms resistor
    9. 4x18650 battery holder
    10. 4pcs 18650 battery -- i've took it from old laptop battery
    11. 550 dc motor -- i've took it from the old ink-jet printer
    12. MG90S -- servo for steering mechanics
    13. 2pcs 3mm red LED -- for the tail lights
    14. 2pcs 3mm white LED -- for the reverse lights
    15. 2pcs 5mm red LED -- for the brake lights
    16. 2pcs 5050 white LED -- for the headlights
    17. 2pcs 30 Degree Angle Lens for 5050 LEDs
    18. SS12D00G4 -- 2 Position 3 Pin Slide Switch

    Also, connectors, wires and 40x40mm breadboard

    For the RC Pad

    1. Arduino Nano -- controller_
    2. NRF24L01+ -- 2.4GHz radio module
    3. XY-016 -- DC-DC Boost converter
    4. 2pcs KY-023 -- XY-axis joystick module
    5. 100uF 16V capacitor -- for radio module
    6. 12x12 push button
    7. SS12D00G4 -- 2 Position 3 Pin Slide Switch
    8. 3mm green LED -- 'ready' indicator
    9. 1x18650 battery holder
    10. 18650 battery

    Arduino firmware source can be taken from here:
    https://gitlab.com/bp3_niva/rc-car/tree/master/Firmware%20Sources

    Assembly instructions are not ready yet -- but i'll add it here once it get finished

    Pls feel free to ask if you have any questions