G27 Shifters v2

This is the new version of my G27 shifters, here's what's new:

An accent ring to add color to the Short and Long shifters.
A customizable cap (I added a plain version if you want to make a custom cap for your shifter, If you do I would like to see it and maybe use it).
A new ball shifter with a removable grip to print it in tpu.
Wall holders for the shifters and the accent ring and caps.

DETAILS;

Shifters:

1- Custom size;

The G27_Long_shifter_v2_part_1 will connect the g27 shifter shaft to a 11 mm steel rebar.
You can make the rebar the length you want.
I don't know if it's normal but my rebar was slightly oval (by a 1mm difference) so I had to make the holes oval, so if you have issues inserting it maybe try rotating it as it
may be oval too.
The G27_Long_shifter_v2_part_2 will connect the 11 mm steel rebar to the G27 Shifters grip v2.
It can be fitted with an accent ring and a cap.

2-Short shifter;

The G27_Short_shifter_v2 will connect the g27 shifter shaft to the G27 Shifters grip v2.
Shorter and more casual looking shifter then the Custom sized ones (also because not everyone has 11 mm rebar laying around :) ).
It can be fitted with an accent ring and a cap.

3-Ball shifter;

It is slightly bigger then the normal g27 ball shifter.
It can be fitted with a cap.

Accessories:

1 Accent ring:

It clips in the groove in the shifter grip.

2 Cap:

It can be pressed into the top of the long, short and ball shifters (install the grips before pressing the cap in).

Wall holders:

All wall holders have reccess holes to stick double sided tape

1 Shifters holders:

G27_Shifter_wall_holder_part_1 supports the adapter side of your shifter (see photos if it's not clear).
G27_Shifter_wall_holder_part_2 supports the grip side of your shifter (see photos if it's not clear).
G27_Ball_shifter_wall_holder supports the ball shifter by the hole on the bottom.

2 Accessories holder:

G27_Shifters_accessories_wall_holder_part_1 holds up to 8 caps.
G27_Shifters_accessories_wall_holder_part_2 needs to be glued to G27_Shifters_accessories_wall_holder_part_1 and holds up to 10 accent rings.

PRINTING SETTINGS;

Shifters:

1-Custom size;

G27_Long_shifter_v2_part_1 needs to be printed flat (flat side up) with 15% infill and supports (BP only).
G27_Long_shifter_v2_part_2 needs to be printed flat (flat side up) with 15% infill and supports (BP only).
G27 Shifters grip v2 needs to be printed standing up with 15% giroid infill (I printed mines in 5% with infill, and it is REALLY squishy, maybe too much) . The grip should be printed in TPU for better comfort altought if you don't have some, pla should work fine too.

2-Short shifter;

G27_Short_shifter_v2_1 should be printed flat (flat side up) with 15% infill and supports (BP only).
-The grip is the same as the custom size one.

3-Ball shifter;

G27_Ball_shifter_v2 should be printed side ways (flat side up) with 15% infill and supports (BP only).
G27_Ball_shifter_v2_grip should be printed standing up with 15% giroid infill and supports (BP only). The grip should be printed in TPU for better comfort altought if you don't have some, pla should work fine too.

Accessories:

G27_Shifter_grip_v2_accent_ring should be printed flat with 100% infill and no supports.
-Both G27_Shifter_grip_v2_cap_blank and G27_Shifter_grip_v2_cap_patern needs to be printed with the half circle touching the buildplate with 15 % infill and supports (BP only).

Wall holders:

G27_Shifters_accessories_wall_holder_part_1 should be printed with the under side touching the build plate with 15% infill and supports (BP only).
G27_Shifters_accessories_wall_holder_part_2 should be printed with the connecting part facing up with 15% infill and supports (BP only).
All: G27_Shifter_wall_holder_part_1 , G27_Shifter_wall_holder_part_2 and G27_Ball_shifter_wall_holder should be printed like they will be on the wall with 15% infill and supports (BP only).

EXTRA INFO;

ALL of the holes that fit in the g27 shifter shaft can be very tight in the begining but with a bit of deburring and putting it on and off it should loosen up to a point where it won't come out on its own but it is easy to remove.

I used pla+ for everything exept the grips but regular pla should be strong enough.